• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Changing your door lock is an easy and inexpensive way to increase the security of your home. However, the procedure is not for everyone. It requires a certain amount of patience and skill.

It is necessary to replace the cylinder that is located within the knob's body. The cylinder is responsible for recognizing the key when it is put into the lock.

Removal of the old double glazing window lock repairs

The first step in replacing the door lock is to take out the old one. It's a fairly simple procedure, but there are a few things to remember. First, make sure that your new lock is the right size for your door. This will ensure that it is securely fitted and won't create a gap around the latch or deadbolt.

Once you have removed the latch plate, look for two screws or bolts on the inside of the casing that connect the casing and two halves of the lock together. Unscrew them using the help of a screwdriver, and then pull the upvc window lock mechanism replacement out of the window door lock repair. If you have a mortise locking system there is a set screw that binds the handle to the spindle. Make use of a screwdriver for removing the screw, and then take out the doorknobs.

You should also remove the latch and deadbolt plug from the hole in your door jamb. Then, you can install your new lock. If you are replacing a mortise you must measure the distance between your lock case and your door edge to ensure that the new lock will fit.

Several reasons might prompt you to replace the door lock, for instance suspecting that someone else has the key or welcoming a new roommate. In any case, you can save money by taking the lock off yourself rather than paying an expert to do it. It's easier than many people think, and it can be completed in a few minutes.

Begin by taking the trim and handle from the window door repairs locks glass hinges. With a flat screwdriver, pry off the trim. You should be able twist off the majority of it. In certain cases you may be able remove the handles completely. The next step is to look for a pinhole on the inside of the handle, and insert straightened clips into it. This will trigger the release mechanism, allowing you to take off the handle. Then, look on the interior side of the lock for a small tab and press it using a flat screwdriver. Once the spindle is removed, you can take off the cylinder and the housing.

The process of selecting a new lock

When it comes time to pick the right lock for your home, you have many options. Take a look at various types of locks, and choose one that is compatible with your door's style. Think about the backset, which is the distance between the edge and the middle of lock hole. Also, consider the cross bore, a small hole at the edge of your door's frame. Also, be sure to choose a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded the majority of door locks to give you an idea of their longevity and the difficulty to pick them up or disable them. A grade 3 lock may be ideal for a quiet suburban apartment complex, whereas a grade 1 lock might hold up better to the traffic at a busy retail storefront on a busy street.

Most smart door locks require digital code to open. If you are concerned about hacking, or other security concerns, consult an expert locksmith.

Replacing the cylinder

You can easily replace damaged or broken doors lock cylinder with a simple DIY project. It is crucial to choose the correct cylinder and follow all instructions. First, you must remove the knob or handle, if it is present. Then, using a screwdriver, remove the trim that is around the lock cylinder. Once the trim has been removed, you will be able to access the screws that hold the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently pulled out of the door.

Be sure to take measurements of the length of the new cylinder prior to installing it. With a tape measure, determine the distance between the center of the cylinder and the left and right side. Purchase a new cylinder that has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key gets stuck inside.

Install the Replacement Window Locks cylinder into the door and then turn the key. This will align the cylinder with the carrier that is usually located on the outside of the lock. Then, loosen the set screw which is supposed to be a few turns in the head. Also, you will need to loosen the screw at the edge of the door that fastens the case, if there is one.

You can replace the lock cylinder you have used with a new one by inserting it into the case and then tightening the set screws. You should also reinstall the part that connects the cylinder with the lock indicator stem and this can be done by pulling up three tabs on the back of the cylinder with needle-nose pliers. Then, you'll be able to attach the smaller bracket to the back of the cylinder. Then, you must install the strike plate and latch plate as well as the retaining ring that is attached to the top lock cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. Most locksets for residential use have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is more thick, you will need an extra-thick door kit that includes longer screws and longer tail pieces (for door knobs) or spindle extension (for deadbolts).

Most locks come with a detailed installation guide to aid you. Before beginning, you must read the instructions to ensure you've followed all the steps. The booklet will also provide you with an idea of the level of skill required to accomplish the task. You may want to ask a friend who has worked with locks for assistance if are changing a lock the first time.

Before installing the new lock, it's a good idea to cover the holes with tape the old hardware. This will keep the screws from falling out of the holes and will safeguard any tile you may have installed in the area. It also protects against potential damage from rust dirt, and grime. SECURAM Touch includes a strip of masking or gaffer tape, but you can make use of any tape you have.

Once you've removed the screws that hold the interior half of the lock section to the outside side, pull it straight away. It's important to do this quickly to avoid the lock from accidentally closing on itself and damage the mechanism.

If your new lock has an internal latch bolt, insert the new bolt into its upper cross bore. Make sure that you place it in the correct location, which is indicated by an arrow. Next, fit the latch plate over the bolt and secure it in the correct position.

Screw the deadbolt into the jamb of the door. Test the deadbolt a few times, throwing it around to ensure it is extending into the strike plate. Follow the instructions included with your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying you identity and connecting to the wireless network to add your device.