• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can repair a loose hinge. If, however, the screw holes are damaged and aren't able to hold screws, you may need to put in dowels and wood glue before you can reinstall the hinge.

Clean up any surface that has rust. This will help to keep the dowels in their place and provide a solid foundation for them to rest on.

Removing the Hinges

Many hinges for doors can be removed, making it simpler to move the door from one end of the frame to the opposite side or remove the entire door when needed. Anyone who is patient can remove the hinges, however, you must know what to do.

If the hinges are painted, you'll need to get rid of the paint before attempting to remove the pins. If you don't, the paint will be smashed off and scratch the door when you attempt to lift it. To break the seal of the paint, place the hinges in a stainless steel pan and fill the pan with water until the hinges are completely submerged. Allow the hinges to sit in the pan for approximately 30 minutes. The heat from the water will soften the paint making it easier to remove.

Once the pins have been loose, remove the hinges and frame from the door. You can employ a screwdriver for the job done, however it is recommended that you make use of a magnetic screwdriver for this project. This type of screwdriver has been specially designed to pick up metal screws and will aid you in getting the job accomplished much faster.

Before you attempt to remove the hinges, it is a good idea to spray them with some oil. A simple lubricant will allow you speed up the process and also remove the screws and pins easier. This type of lubricant can be found in a variety of hardware stores and home improvement stores.

It is important to keep in mind that the number of hinges you'll need will differ based on the door's type and its setting. Doors with solid cores and heavy weights will require more hinges whereas hollow-cored and lighter doors might only need two or three.

It is also essential to know the various types of hinges to decide which one will best suit your needs. The hinges on the exterior are designed to hold the weight of a door, whereas interior hinges need to be able to handle heavier loads.

Reattaching the Hinges

Over time, a door hinge can loosen and begin to slide or hang crookedly. This can be a problem but is usually easy to solve. A simple retightening will usually solve the issue. If the screw holes have been ripped out, it may be difficult to do. Fortunately, there is a trick to make the holes back in place that uses a wood dowel.

Begin by drilling the hole using a drill bit close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length exactly the same as the screw to ensure a tight fit. Then, you can reinstall the screw and tighten it until the desired level of tightness. If the door has the tendency to be bowed, then add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to make sure that the clearances around the perimeter are correct.

You can also use a wooden plug in place of the dowel. This is also a viable option however it will take a bit longer to install. You can use a piece of wood which has been cut to the proper size. If you don't have an instrument for woodworking or toothpicks, you can make use of toothpicks or wooden matchsticks.

Use a countersink to make the hole smaller for the head of screw after you have put it back in place. This will stop the screw from rubbing against the edges of the doors when they are closed and opened. This will make it easier to tighten the screw after you are reinstalling the hinge.

After reinstalling the hinge, make sure to lubricate the hinge using dry lubricant. This will prevent it from becoming stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. Apply a thin coat and wait for about 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you could make a few minor repairs. Verify that the screws that secure the hinge plate to the door frame and the frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be careful not to over tighten the screws, as this could create gaps at the trim joints, or worse, strip out the threads.

If the issue is that the hinge plates are breaking away from the door and jamb, you can reattach them by applying wood glue to the plate's back and then inserting wooden dowels or toothpicks into the holes. The toothpicks and dowels provide an solid foundation for the screws, preventing the plates from shifting when you insert them. Let the glue dry before reattaching the hinge.

The screws may also be stripped or missing. This problem can be fixed by replacing the screws. Be sure to use the correct drill bit for the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

Close the door once you've reattached the hinge and measure the gap between the frame and the door. It should be approximately the thickness of a nickel all around, or less if there's an existing gap caused by a previous door that was not properly hang. If the hinges were set up correctly, this should not be an issue.

If you discover that the hinges remain loose, try adding a thicker hinge shim between the hinge plate and the mounting surface to give some extra space. You can also remove the hinge pin, then pound it down with a hammer to tighten it, or install the hinge of a different type. It is also possible to lubricate the upvc window hinges with mineral or Jojoba oil to reduce friction and help them hold their position. Lubricating your hinges regularly can prevent them from becoming stiff and squeaky, and can also prolong their life.

Cleaning the Hinges

The friction hinges for upvc windows created by the hinge's constant motion attracts dust particles. Without periodic cleaning and lubrication, these particles get stuck in the moving parts of a Double Glazed Window Hinge Repair for doors and then build up over time. As a result the hinge becomes stiff and creaky and its appearance may be damaged quickly. Regular cleaning, lubrication and inspections will ensure the functionality and quality of hinges that are attached to doors.

Examine the hinges to determine how much rust has built up on their surfaces. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you can save the hinges, first brush away loose rust using steel wool and a wire brush. Apply a commercial rust removal solution or homemade solutions like lemon juice on the hinge. Let the rust remover remain on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

Retightening screws can restore hinge function if you don't want to spend time or money to replace upvc energy efficient window hinge hinges. If you've sanded the screw holes, however, it may be necessary to attach a wooden dowel or shim to the hinge. Wooden dowels come in round rods of various sizes and lengths. You can buy them online, in woodworking supply shops and at home improvement stores.

A shim could be made of metal or plastic, depending on the kind of hinge you've got. To make a dowel, cut an unfinished dowel into the desired length. You can then dip the dowel into a carpenter's glue and insert it into the cut hole, allowing the glue to hold the dowel in place.

Before you start cleaning the hinges, put down a paper or cloth towel to shield floors and other surfaces from spills and drips that may happen. After the area is secured, proceed to clean the hinges with a soft sponge or cloth coated with a mild cleaner or vinegar to eliminate dirt, grime, and tarnish. A toothbrush or small brush can be used to access hard-to-reach areas in crevices and tight spots.