Reasons Your fiat car keys cut 500 Key Fob Won't Work

A key fob for the fiat 500 all keys lost 500 makes it easy to open doors and start your car. There are a variety of reasons why the fob won't work. These include a dead coin battery damaged receiver module, water damage issues, and interference.

This listing is for a NEW replacement fiat replacement key fob Flip Key Remote - look-alike Ilco brand that needs to be professionally programmed by a local locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't function is due to an inactive battery. Modern key fobs offer only a limited range of operation and must be within only a few inches from the vehicle in order to function. If you are far from your vehicle and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. They are typically available at your local hardware store or online.

After you've replaced the battery of your coin cell You can test it by standing close to your fiat 500 abarth key fob replacement 500 and pressing the buttons. The car will blink its parking lights and the key fob should work the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it might have water damage that stops it from communicating with the receiver module inside your car. Water damage can occur in many ways, including an easy splash or submerging the key fob in saltwater at the beach. If you believe your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this doesn't work, you will require your fob to be reset by an auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob into the ocean or wash it in a machine. Saltwater can cause the circuit board to short and then cease to function. It's not good to submerge the fob in water, but don't give it up even if you accidentally drop the fob in water, or fail to remove it from your pants pocket.

Remove the battery first. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Test the fob next to check if it's working. If the key does not function, it may have to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is a newer model and has never been programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars can carry out this simple task. The locksmith must cut the key to match the ignition in your vehicle. The locksmith also needs to reprogram your fob into the car's system. This is an affordable and quick procedure that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob may stop functioning is that it's out of range. The remote typically has an operating range of 30 feet or less and if it's far away from your car it will not respond to your commands. It is possible to fix this by moving the remote closer to your vehicle until it responds.

If your fob won't work after replacing the coin battery, also known as a "button", "watch" or "button" or "button", it may be due to a malfunction on the internal circuit board. Reprogramming your fob can resolve the issue. You can find the steps for the majority of vehicles on YouTube or in the owner's manual.

You may need to replace the metal retaining clips that keep the battery of your coin in place. If they lose tension it could hinder the battery from being seated properly, and this will result in the malfunction of your remote.

In rare cases the fob might become desync'd with your vehicle due to software issues or hardware issues. This could cause a significant problem, but you can usually resolve this issue by visiting an auto locksmith to reprogram your fob for you. In certain instances they may have to reinstall the software in your body control module as well.

Interference

In addition to a dead coin battery the key fob could not be able to transmit or receive the signal due to interference. This is possible when the key fob is close to an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob may not work due to a poor connection to the buttons water damage or damage to the internal chips.

If the key fob been unable to function for a while out of the blue or even after trying everything you can do at home to fix it e.g. It could be a defective 500 receiver module after you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electric current, and also restart the car's computer. This could help you get your key fob to function again. If the problem persists you should consult an expert technician. They can determine the exact cause of your problems.