How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with a keyless entry system built into. The key can be compared to the remote control and is able to be replaced with a brand new one from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including batteries that are dead, worn-out buttons signal interference or water damage. Here are some helpful tips to help you get your 2018 kia sportage key fob programming sportage replacement key for kia picanto key to work once more.

How do you replace a remote key or smartkey

It doesn't matter if your Kia comes with an intelligent key, remote key, push to start key, or regular metal non-transponder key The battery inside these keys will eventually require replacing. This is especially when the vehicle displays a message that indicates that the remote or smart key is not powered by the battery.

Fortunately, it's quite simple to do. In order to replace the battery in the key fob remove the mechanical key from the hole in the back of the key fob. Next, lift the cover. A small screw is located inside the key fob, which holds the battery in its place. Take out the old battery by unwinding the screw with the help of a small screwdriver. Insert the new battery and close the cut on the key fob.

Test the key fob by pressing the lock and unlock buttons. It's okay if the doors lock and unlock as you expect. You can now make use of your Kia's hands-free lock/unlock feature when your fingers start to get cold or you need to run some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a computer that is only available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) do not require programming. If your key needs to be programmed again, you must be aware of the number that is stamped on the tag of the key code and record it in a safe location.

How to replace a battery

If the kia soul key fob programming key fob does not respond to pressing the lock or unlock button, it is likely that the battery is insufficient. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not working properly. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires only a few tools.

Make sure to shut off your vehicle and close all doors before you begin. Find the small metal or plastic piece near the bottom of the key fob. Move it until the metal key is released. The key can be placed inside the driver door handle to unlock your duplicate car keys cost.

To replace the battery inside the key fob, remove the rear cover. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then position the new battery so that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

Once the new battery has been installed then turn the key fob off and then on in the ignition for a few times until the door locks. You can then test the Kia's Key fob once more to ensure it is working correctly.

How do you replace the smart key

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The difference between the two is that the smart fob has tiny mechanical key blade in it, whereas the standard fob does not. Both key fobs have an internal battery that will eventually need to be changed. It is a simple process that takes less than two minutes.

Make sure you turn off your Kia and be on a flat well-lit and well-lit area before you begin. Also, keep in mind that there are tiny parts inside the fob which could fall out if you are not cautious.

The small release button is located on the lower backside. This will be either a circular button or rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, remove the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. After installation it should be possible to lock, unlock and start your vehicle with your key fob, even if your engine isn't running!

How do I replace the mechanical key?

The 2013 kia rio key replacement keyfob is an excellent convenience which allows us to lock or unlock our car with just pressing the button. Like any other device it will encounter issues from time to time. There are ways to resolve these issues and keep your key fobs working for a long time.

One of the most frequently encountered issues is a low or dead battery. This can cause your device to stop working or operate intermittently. If this is the case try replacing the battery with a new one.

If this doesn't fix the problem then try using a normal flathead screwdriver to open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the fob to make sure it's working as intended. If the key fob isn't working, contact a locksmith or dealer to resolve the issue. To avoid future lockouts, ensure you purchase an emergency key that will work in all of the door and trunk cylinders.